Synchronous Generator House Diagram For An Essay

The electrical machine can be defined as a device that converts electrical energy into mechanical energy or mechanical energy into electrical energy. An electrical generator can be defined as an electrical machine that converts mechanical energy into electrical energy. An electrical generator typically consists of two parts; stator and rotor. There are various types of electrical generators such as direct current generators, alternating current generators, vehicular generators, human powered electrical generators, and so on. In this article, let us discuss about synchronous generator working principle.

Synchronous Generator

The rotating and stationary parts of an electrical machine can be called as rotor and stator respectively. The rotor or stator of electrical machines acts as a power-producing component and is called as an armature. The electromagnets or permanent magnets mounted on the stator or rotor are used to provide magnetic field of an electrical machine. The generator in which permanent magnet is used instead of coil to provide excitation field is termed as permanent magnet synchronous generator or also simply called as synchronous generator.

Construction of Synchronous Generator

In general, synchronous generator consists of two parts rotor and stator. The rotor part consists of field poles and stator part consists of armature conductors. The rotation of field poles in the presence of armature conductors induces an alternating voltage which results in electrical power generation.

The speed of field poles is synchronous speed and is given by

Where, ‘f’ indicates alternating current frequency and ‘P’ indicates number of poles.

Synchronous Generator Working Principle

The principle of operation of synchronous generator is electromagnetic induction. If there exits a relative motion between the flux and conductors, then an emf is induced in the conductors. To understand the synchronous generator working principle, let us consider two opposite magnetic poles in between them a rectangular coil or turn is placed as shown in the below figure.

If the rectangular turn rotates in clockwise direction against axis a-b as shown in the below figure, then after completing 90 degrees rotation the conductor sides AB and CD comes in front of the S-pole and N-pole respectively. Thus, now we can say that the conductor tangential motion is perpendicular to magnetic flux lines from north to south pole.

So, here rate of flux cutting by the conductor is maximum and induces current in the conductor, the direction of the induced current can be determined using Fleming’s right hand rule. Thus, we can say that current will pass from A to B and from C to D. If the conductor is rotated in a clockwise direction for another 90 degrees, then it will come to a vertical position as shown in the below figure.

Now, the position of conductor and magnetic flux lines are parallel to each other and thus, no flux is cutting and no current will be induced in the conductor. Then, while the conductor rotates from clockwise for another 90 degrees, then rectangular turn comes to a horizontal position as shown in the below figure. Such that, the conductors AB and CD are under the N-pole and S-pole respectively. By applying Fleming’s right hand rule, current induces in conductor AB from point B to A and current induces in a conductor CD from point D to C.

So, the direction of current can be indicated as A – D – C – B and direction of current for the previous horizontal position of rectangular turn is A – B – C – D. If the turn is again rotated towards vertical position, then the induced current again reduces to zero. Thus, for one complete revolution of rectangular turn the current in the conductor reaches to maximum & reduces to zero and then in the opposite direction it reaches to maximum & again reaches to zero. Hence, one complete revolution of rectangular turn produces one full sine wave of current induced in the conductor which can be termed as the generation of alternating current by rotating a turn inside a magnetic field.

Now, if we consider a practical synchronous generator, then field magnets rotate between the stationary armature conductors. The synchronous generator rotor and shaft or turbine blades are mechanically coupled to each other and rotates at synchronous speed. Thus, the magnetic flux cutting produces an induced emf which causes the current flow in armature conductors. Thus, for each winding the current flows in one direction for the first half cycle and current flows in the other direction for the second half cycle with a time lag of 120 degrees (as they displaced by 120 degrees). Hence, the output power of synchronous generator can be shown as below figure.

Do you want to know more about synchronous generators and are you interested in designing electronics projects? Feel free to share your views, ideas, suggestions, queries, and comments in the comment section below.

Related Content

In recent years, distributed electrical power generation systems have attracted more attention due to their small scale technologies, lower cost electricity generation and higher reliability and security with fewer environmental consequences, rather than traditional power generators. Different applications such as peak saving, cogeneration, remote power and premium power will make it more and more useful. On the other hand, the permanent magnet synchronous generators, driven by micro turbines, play an important role in the distributed power generation systems. These PM generators produce a high frequency electrical power which needs to be converted to the usual power frequency, 50 or 60 Hz. This conversion is usually done using a back to back combination of rectifier, DC-link and inverter. The main focus of this paper is to present a model for a voltage source rectifier which is connected to a PM generator in a micro turbine unit, where Virtual Flux based Direct Power Control strategy is used to control the mentioned rectifier. The simulation results, using Matlab/Simulink, are presented to show the validity of the proposed model for the PWM rectifier, and to evaluate the performance of the control strategy.

Leave a Comment

(0 Comments)

Your email address will not be published. Required fields are marked *